This word is used for that one annoying kid named Jayrome. He thinks everyone hates him just because of a simple un-add on discord. Jayrome thinks he’s the main character too! If he’s being a dick hole, just scream “HEUGH 3DS”
by butt ass naked jr February 28, 2025
Get the HEUGH 3DS!!mug. When you heat the tip of your penis with a kettle, you cum and shit yourself at the same time, therefore using that steamy cum as glue for 3d printed sculptures.
by youdontwannaknow222 February 21, 2024
Get the The 3D Printer Manouvermug. The most extreme form of being doomed...
You've gone through doomed to quaked to wolfenstine3ded to kens labyrinthed and all the way to Super 3d noa's arked.....
Truly the pinnacle of 3d shooter expressed screwed upedness...
You've gone through doomed to quaked to wolfenstine3ded to kens labyrinthed and all the way to Super 3d noa's arked.....
Truly the pinnacle of 3d shooter expressed screwed upedness...
OH fuck! i am soo doomed!
I have no idea what to get anyone for x-mas!
I am doomed! no wait it worse then that I'm wolfenstin 3ded! no wait worse still I'm kens labyrinthed....
Hell I 'm probably Super 3d noa's arked!
I have no idea what to get anyone for x-mas!
I am doomed! no wait it worse then that I'm wolfenstin 3ded! no wait worse still I'm kens labyrinthed....
Hell I 'm probably Super 3d noa's arked!
by Qrez December 16, 2016
Get the super 3d noa's arkedmug. by SuckMyWalugi August 22, 2017
Get the The 3d planmug. by The Manager of 3D November 12, 2012
Get the 3Dmug. by pintoloco October 1, 2020
Get the potaty 3dmug. Ammunition for 3d youtube firearm 1,2,3
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
by Cody5050 May 21, 2023
Get the 3d youtube firearm 5mug.