by periodwithtrans February 2, 2023
Get the 3d giffs thsat sucmug. by Infinite369 May 29, 2022
Get the 3D Wristmug. Team 3D was a legendary tag team formed in the Attitude Era when wrestling was becoming popular around the world. Mostly known for their hardcore and table spots. Also known for their feuds with Edge and Christian and The Hardy Boyz and known for their storyline with Trish Stratus. Members:Devon Dudley and Bubba Ray Dudley. also a lesser known member and known as a crazy little man.... Spike Dudley!
by WarWrestlingDefinitions June 13, 2016
Get the Team 3Dmug. Ammunition for 3d youtube firearm 1,2,3
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
by Cody5050 May 21, 2023
Get the 3d youtube firearm 5mug. by Thomanory June 11, 2021
Get the Saw 3Dmug. by squillam June 9, 2023
Get the I don't play Duke Nukem 3Dmug.