This word is used for that one annoying kid named Jayrome. He thinks everyone hates him just because of a simple un-add on discord. Jayrome thinks he’s the main character too! If he’s being a dick hole, just scream “HEUGH 3DS”
by butt ass naked jr February 28, 2025
Get the HEUGH 3DS!! mug.by I like to scare little kids January 24, 2022
Get the Paint 3D mug.Ammunition for 3d youtube firearm 1,2,3
Gunpowder, also known as black powder, is a mixture of three main ingredients: potassium nitrate (also known as saltpeter), charcoal, and sulfur. The ingredients are mixed together in specific proportions and then ground into a fine powder.
The traditional formula for gunpowder is 75% saltpeter, 15% charcoal, and 10% sulfur by weight. However, the proportions can vary depending on the desired properties of the powder.
To mix the ingredients, they are typically pulverized separately and then combined in a mixing bowl or mortar and pestle. The mixture is then ground and blended thoroughly until it forms a homogenous powder.
It is important to note that creating gunpowder can be dangerous and requires specialized knowledge, equipment, and permits. It is not recommended for individuals without proper training and experience to attempt to make their own gunpowder.
Gunpowder, also known as black powder, is a mixture of three main ingredients: potassium nitrate (also known as saltpeter), charcoal, and sulfur. The ingredients are mixed together in specific proportions and then ground into a fine powder.
The traditional formula for gunpowder is 75% saltpeter, 15% charcoal, and 10% sulfur by weight. However, the proportions can vary depending on the desired properties of the powder.
To mix the ingredients, they are typically pulverized separately and then combined in a mixing bowl or mortar and pestle. The mixture is then ground and blended thoroughly until it forms a homogenous powder.
It is important to note that creating gunpowder can be dangerous and requires specialized knowledge, equipment, and permits. It is not recommended for individuals without proper training and experience to attempt to make their own gunpowder.
by Cody5050 May 21, 2023
Get the 3d youtube firearm 6 mug.The month where everything is supposed to be on 3D form especially magazines and newspapers! It’s wicked
Mum: the colours in this magazine are ALL wrong
Me: Hahhah no Mum you retard. You have to wear 3D glasses because it’s July 3D
Me: Hahhah no Mum you retard. You have to wear 3D glasses because it’s July 3D
by lexiifire23 July 15, 2020
Get the July 3D mug.by squillam June 9, 2023
Get the I don't play Duke Nukem 3D mug.The game home to the overworld theme that you interrupt every other song with -Toad: Commander of Plasti Dip
3D Land is very plasti.
by Dishwasher age February 1, 2018
Get the 3D Land mug.Ammunition for 3d youtube firearm 1,2,3
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
by Cody5050 May 21, 2023
Get the 3d youtube firearm 5 mug.