1 - 2L plastic pop bottle
1 - smaller pop bottle
1 - piece of tin foil
1 - knife
1 - needle
1 - lighter
2 - litre of water
? - tape
1 - lighter
? - weed
1. Cut the skinny part of the large pop bottle off. (Cut right where it starts to go from really big to really small).
2. Fill the bottle with water (as full as you can without having it spill).
3. In the lid of the smaller pop bottle, make a hole about the size of a penny carefully with the knife.
4. Place the tin foil in the hole and make a small indent into it (to hold the weed in).
5. Tape the tin foil at the sides (try not to get any tin foil or tape on inside of the lid or it wont screw on the bottle well), and make several tiny wholes in the tin foil with the needle.
6. In the small pop bottle, there should be 5 'thingies' at the bottom. Cut fairly small holes in 3-5 of them. Then place the small bottle inside the large bottle.
7. Once the smaller bottle has been submerged in the water, put your weed in the lide and screw the lid on.
8. At the same time as you light the weed, lift the smaller bottle out of the water slowly. The water pressure will fill the bottle with all the smoke.
9. Once the bottle is completely filled with smoke and there is no water left, them put your mouth around the top, dip the bottom back in the water, and then lift it back out and inhale at the same time.
10. If this is your first time, or you don't smoke a lot, you may green out (throw up) several times. But it's worth it. You will get completely f***ed without using as much weed as a joint, and you will get like 10 times higher with this as you would with a joint. You only need like 2-3 hits to get really stoned, but do as many as you like. :)
Legal Disclaimer: The above was intended for educational purposes only. I do not encourage the use of marijuana or other illegal drugs (except in countries/regions where it is 100% legal).
1 - smaller pop bottle
1 - piece of tin foil
1 - knife
1 - needle
1 - lighter
2 - litre of water
? - tape
1 - lighter
? - weed
1. Cut the skinny part of the large pop bottle off. (Cut right where it starts to go from really big to really small).
2. Fill the bottle with water (as full as you can without having it spill).
3. In the lid of the smaller pop bottle, make a hole about the size of a penny carefully with the knife.
4. Place the tin foil in the hole and make a small indent into it (to hold the weed in).
5. Tape the tin foil at the sides (try not to get any tin foil or tape on inside of the lid or it wont screw on the bottle well), and make several tiny wholes in the tin foil with the needle.
6. In the small pop bottle, there should be 5 'thingies' at the bottom. Cut fairly small holes in 3-5 of them. Then place the small bottle inside the large bottle.
7. Once the smaller bottle has been submerged in the water, put your weed in the lide and screw the lid on.
8. At the same time as you light the weed, lift the smaller bottle out of the water slowly. The water pressure will fill the bottle with all the smoke.
9. Once the bottle is completely filled with smoke and there is no water left, them put your mouth around the top, dip the bottom back in the water, and then lift it back out and inhale at the same time.
10. If this is your first time, or you don't smoke a lot, you may green out (throw up) several times. But it's worth it. You will get completely f***ed without using as much weed as a joint, and you will get like 10 times higher with this as you would with a joint. You only need like 2-3 hits to get really stoned, but do as many as you like. :)
Legal Disclaimer: The above was intended for educational purposes only. I do not encourage the use of marijuana or other illegal drugs (except in countries/regions where it is 100% legal).
by Adam George March 21, 2008
Get the bucket bongmug. When you sprinkle grinded up Marijuana on your boyfriends pubes and when he bust a nut, you suck on his dick while lighting his pubes on fire. Call that a bong rip.
by Leetist1337 May 16, 2016
Get the Bong ripmug. When you pin someone down, press on their chest until they can't breath while holding a gasmask hooked up to a bong on their face against their will.
by xtoothdecay May 1, 2010
Get the bong rapemug. bong mods is the term used when you modify a bong (usually a smaller one) to make it work better or just to change the way you hit it. commonly used bong mod materials are water bottles, clear tape, masking tape, pens, and toliet paper rolls.
*Adding paper towell rolls to small bongs to make the tube taller creating a awesome bong mod!
*Adding a self-lighting device
*Vaporizing system bong mods????
the possibilities are endless!
*Adding a self-lighting device
*Vaporizing system bong mods????
the possibilities are endless!
by YonderMountainRamblin February 9, 2010
Get the bong modsmug. Are homemade bongs that originated in Australia in the 1990's they are usually made out of sports drink bottles and garden hoses and metal cone's as bowls. This technique is very popular amongst teenagers or young people with not enough money to just buy a bong from a headshop or are under the age of 18 and can't yet buy one. This technique is also very popular in the U.S. (also with teenagers) but instead of a garden hose and metal cone it is usually a hollowed out pen and a metal socket.
by dltn420_666 March 21, 2012
Get the Aussie Bongmug. The act of folding a paper plate in half and putting it into your mouth funnel style to get the last bits of goetta off the plate. Usually performed at Goetta Fest although socially acceptable anywhere goetta is served on paper plates.
by the wicked chica August 21, 2010
Get the Goetta Bongmug. The callous you get from lighting bong hits with a bic lighter, repeatedly. Usually found on the index finger.
by Drgizmo July 22, 2010
Get the Bong Fingermug.