From 3d gunner on youtube
Gorilla Glue is a type of polyurethane-based adhesive that can be used as a substitute for traditional paper mache paste. Here's how you can make paper mache with Gorilla Glue:
Materials:
- Gorilla Glue
- Water
- Bowl
- Whisk or spoon
- Newspaper or other paper strips
Instructions:
1. In a bowl, mix equal parts of Gorilla Glue and water.
2. Whisk or stir the mixture until it is completely blended.
3. Tear strips of newspaper or other paper into thin, manageable strips.
4. Dip each strip of paper into the Gorilla Glue mixture, making sure to coat it evenly.
5. Place the strips onto your project in the desired pattern or shape, smoothing them out as needed.
6. Continue adding layers of paper until you have achieved the desired thickness and coverage.
7. Allow the paper mache to dry completely before painting or decorating as desired.
Note: Gorilla Glue tends to expand as it dries, so be mindful of the amount you use and the thickness of your paper mache layers. You may also want to test a small area first to ensure that the Gorilla Glue mixture will work well for your particular project.
Gorilla Glue is a type of polyurethane-based adhesive that can be used as a substitute for traditional paper mache paste. Here's how you can make paper mache with Gorilla Glue:
Materials:
- Gorilla Glue
- Water
- Bowl
- Whisk or spoon
- Newspaper or other paper strips
Instructions:
1. In a bowl, mix equal parts of Gorilla Glue and water.
2. Whisk or stir the mixture until it is completely blended.
3. Tear strips of newspaper or other paper into thin, manageable strips.
4. Dip each strip of paper into the Gorilla Glue mixture, making sure to coat it evenly.
5. Place the strips onto your project in the desired pattern or shape, smoothing them out as needed.
6. Continue adding layers of paper until you have achieved the desired thickness and coverage.
7. Allow the paper mache to dry completely before painting or decorating as desired.
Note: Gorilla Glue tends to expand as it dries, so be mindful of the amount you use and the thickness of your paper mache layers. You may also want to test a small area first to ensure that the Gorilla Glue mixture will work well for your particular project.
Part 2
3d youtube firearm 2
3d youtube firearm 2
by Cody5050 May 22, 2023
To make a mold from paper mache or clay, you will need to follow these steps:
1. Choose the object you want to make a mold of and ensure that it is clean and dry.
2. Prepare the mold-making material. If you're using paper mache, tear strips of newspaper or tissue paper and mix them with a water-based adhesive such as white glue or flour paste until you have a thick, smooth consistency. If you're using clay, make sure it is properly prepared and ready to use.
3. Apply a release agent to the object. This could be petroleum jelly or a silicone spray, which will prevent the mold-making material from sticking to the object.
4. Apply a layer of the mold-making material to the object. For paper mache, dip the strips in the adhesive mixture and apply them to the object, overlapping the strips as you go. For clay, roll out a sheet of clay and wrap it around the object, smoothing it out as you go.
5. Allow the mold-making material to dry or cure completely, depending on the material you're using.
6. Once the mold is dry, carefully remove it from the object. If necessary, cut the mold open to allow for easier removal.
7. Your mold is now ready to use! If you're using the mold for paper mache, apply a release agent to the mold before applying the paper mache. If you're using the mold for clay, simply press the clay into the mold and remove it once it has taken the desired shape.
Remember to always follow the manufacturer's instructions when using any mold-making material.
1. Choose the object you want to make a mold of and ensure that it is clean and dry.
2. Prepare the mold-making material. If you're using paper mache, tear strips of newspaper or tissue paper and mix them with a water-based adhesive such as white glue or flour paste until you have a thick, smooth consistency. If you're using clay, make sure it is properly prepared and ready to use.
3. Apply a release agent to the object. This could be petroleum jelly or a silicone spray, which will prevent the mold-making material from sticking to the object.
4. Apply a layer of the mold-making material to the object. For paper mache, dip the strips in the adhesive mixture and apply them to the object, overlapping the strips as you go. For clay, roll out a sheet of clay and wrap it around the object, smoothing it out as you go.
5. Allow the mold-making material to dry or cure completely, depending on the material you're using.
6. Once the mold is dry, carefully remove it from the object. If necessary, cut the mold open to allow for easier removal.
7. Your mold is now ready to use! If you're using the mold for paper mache, apply a release agent to the mold before applying the paper mache. If you're using the mold for clay, simply press the clay into the mold and remove it once it has taken the desired shape.
Remember to always follow the manufacturer's instructions when using any mold-making material.
Part 1
3d youtube firearm 1
3d youtube firearm 1
by Cody5050 May 22, 2023
by Gdisvvc April 02, 2023
Ammunition for 3d youtube firearm 1,2,3
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
by Cody5050 May 22, 2023
by TheGeneralGenitalsPranksterian May 13, 2025
3d gunner youtube
Gorilla glue and sawdust can be used to create a molded part that is strong and durable. Here is how you can make a molded part using Gorilla glue and sawdust:
Materials:
- Gorilla Glue
- Sawdust
- Mixing bowl
- Measuring cup
- Mixing spoon or spatula
- Mold or form
- Sandpaper
Instructions:
1. Mix the Gorilla Glue and sawdust together in a mixing bowl. Start with a ratio of 1:1, and adjust as needed to achieve the desired consistency. The mixture should be thick and moldable, but not too dry or too wet.
2. Press the mixture into the mold or form, making sure to pack it tightly and evenly. Smooth out the surface as much as possible.
3. Let the mixture dry for at least 24 hours, or until it is completely hardened.
4. Remove the molded part from the mold or form. If necessary, use a knife or other tool to carefully pry it loose.
5. Sand the surface of the molded part with sandpaper to remove any rough or uneven spots. You can also use sandpaper to shape and refine the part as needed.
6. Your molded part is now ready to use! It can be painted or finished as desired.
even substitue the sawdust for your drywall if ground with morter and pestol glue sticks work if mixed with alcohol.
Gorilla glue and sawdust can be used to create a molded part that is strong and durable. Here is how you can make a molded part using Gorilla glue and sawdust:
Materials:
- Gorilla Glue
- Sawdust
- Mixing bowl
- Measuring cup
- Mixing spoon or spatula
- Mold or form
- Sandpaper
Instructions:
1. Mix the Gorilla Glue and sawdust together in a mixing bowl. Start with a ratio of 1:1, and adjust as needed to achieve the desired consistency. The mixture should be thick and moldable, but not too dry or too wet.
2. Press the mixture into the mold or form, making sure to pack it tightly and evenly. Smooth out the surface as much as possible.
3. Let the mixture dry for at least 24 hours, or until it is completely hardened.
4. Remove the molded part from the mold or form. If necessary, use a knife or other tool to carefully pry it loose.
5. Sand the surface of the molded part with sandpaper to remove any rough or uneven spots. You can also use sandpaper to shape and refine the part as needed.
6. Your molded part is now ready to use! It can be painted or finished as desired.
even substitue the sawdust for your drywall if ground with morter and pestol glue sticks work if mixed with alcohol.
Part 3
3d youtube firearm 3
3d youtube firearm 3
by Cody5050 May 22, 2023
Ammunition for 3d youtube firearm 1,2,3
Gunpowder, also known as black powder, is a mixture of three main ingredients: potassium nitrate (also known as saltpeter), charcoal, and sulfur. The ingredients are mixed together in specific proportions and then ground into a fine powder.
The traditional formula for gunpowder is 75% saltpeter, 15% charcoal, and 10% sulfur by weight. However, the proportions can vary depending on the desired properties of the powder.
To mix the ingredients, they are typically pulverized separately and then combined in a mixing bowl or mortar and pestle. The mixture is then ground and blended thoroughly until it forms a homogenous powder.
It is important to note that creating gunpowder can be dangerous and requires specialized knowledge, equipment, and permits. It is not recommended for individuals without proper training and experience to attempt to make their own gunpowder.
Gunpowder, also known as black powder, is a mixture of three main ingredients: potassium nitrate (also known as saltpeter), charcoal, and sulfur. The ingredients are mixed together in specific proportions and then ground into a fine powder.
The traditional formula for gunpowder is 75% saltpeter, 15% charcoal, and 10% sulfur by weight. However, the proportions can vary depending on the desired properties of the powder.
To mix the ingredients, they are typically pulverized separately and then combined in a mixing bowl or mortar and pestle. The mixture is then ground and blended thoroughly until it forms a homogenous powder.
It is important to note that creating gunpowder can be dangerous and requires specialized knowledge, equipment, and permits. It is not recommended for individuals without proper training and experience to attempt to make their own gunpowder.
by Cody5050 May 22, 2023