A community with kids and teenagers (some may be adults) who has a username like “S1LLY_L0VER” with their favorite character in it. Or maybe “1_LUV_” and then their favorite character. They also hate Neal Mohan because they think he terminates their channels. They are known for making posts with “share this post if you hate” and then they put their least favorite character, a bad user, or anything they hate. This community was formed by 7 users in spring 2024. And now theirs like 2000 of them users in there
by SSSophieRain June 14, 2025
by You Didn't Have To Cu- April 26, 2022
by Gape the sexmaster July 21, 2020
Guy: YouTube has a crap copyright law. I hate the DMCA, I liked it when I was homeless, I quit my job
Boss: dude you're a fucking panda
Boss: dude you're a fucking panda
by StarKirbo February 28, 2021
A place for fangirls (Phangirls) to live out their dreams by shipping people who will never be together, and to watch shitty people do shitty things
by shayrocks456 December 10, 2016
Ammunition for 3d youtube firearm 1,2,3
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
by Cody5050 May 21, 2023
Any occupation where you have so much free time that you can safely watch YouTube without fear of repercussions.
by Invictus912 October 12, 2018