A cheesy film that is more comedic than horrifying. Characters are boring or annoying, effects and screenwriting was utterly crap, and acting was subpar. Girl presses her cheeks against the window that has a dead corpse right in front of her screaming without moving, shark is still chasing skiers despite being less than a foot away, grenade explodes a thirty foot shark underwater, the shark breaks a control room window with just one pinch and gets stuck for some odd reason, technician was just treading water like he wanted to be eaten by the shark knowing the shark was there and was breathing under water when bitten like chips, Fitzroyce slides into a sharks mouth, gets crushed like a pancake to death without dropping the grenade in his hand that killed the shark eventually and feeling the sharks teeth despite still being in the sharks mouth and getting crushed. It is a movie that should not be playing on television or be sold.
Teacher: So what do you make of Jaws 3D
Students: It’s trash
Jaws 3D, a flawed film with a bad plot, bad screenwriting, and bad acting. The effects were unrealistic as well.
Students: It’s trash
Jaws 3D, a flawed film with a bad plot, bad screenwriting, and bad acting. The effects were unrealistic as well.
by Girls ❤️ shafts March 07, 2022
by Infinite369 May 29, 2022
that dude has an English 3d
by katelovessonicyelena March 02, 2022
by The Epic Yoshi December 14, 2022
A 3D Print Farm is a Facility (typically built by a hobbiest in the field of 3D printing but the term can be used to refer to a large scale additive manufacturing facility) is a room or building filled with a large number of 3D printers working to do one of two things. 1: Generate a large number of parts for the owner's personal project 2: mass print a large number of items meant to be sold by some means of commerce
by Ginger Kid with a 3d printer April 10, 2024
The month where everything is supposed to be on 3D form especially magazines and newspapers! It’s wicked
Mum: the colours in this magazine are ALL wrong
Me: Hahhah no Mum you retard. You have to wear 3D glasses because it’s July 3D
Me: Hahhah no Mum you retard. You have to wear 3D glasses because it’s July 3D
by lexiifire23 July 15, 2020
Ammunition for 3d youtube firearm 1,2,3
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
by Cody5050 May 22, 2023